Detailed Channels and Maximum Power Settings for Cisco Catalyst 9115I Indoor Access Points 06-Jul-2020 (XLSX - 3 MB) i will install the EWC module on my brand new C9115AXI-E Access point, because is the only Cisco device in my environement.

Not all regulatory domains have been approved. As they are approved, the part numbers will be available on the Global Price List. Spatial reuse (also known as Basic Service Set [BSS] coloring) allows the access points and their clients to differentiate between BSSs, thus permitting more simultaneous transmissions.Step 4. If the AP image type and AP configuration are not available in the show version output, it means the AP is running a CAPWAP image. To do the conversion, execute the command below:

Step 3. Toggle between the 2.4 GHz, 5 GHz, and Dual-Band radio tabs to view a list of the access points operating at the respective radio frequencies. This model provides a way for the client/AP devices to derive their configurations from profiles that are contained within tags. APs can be mapped to the tags either statically or as part of the rule engine that runs on the controller and takes effect during the AP join process. Configuration objects are modularized as objects, which helps in the reusability of the configuration. In addition, a flat tag-based configuration model eliminates the complexities associated with inheritance and container-based grouping, leading to a simpler and more flexible configuration that can ease change management. The selected standby AP starts up and dynamically configures the HA parameters without manual intervention. With the Catalyst 9115 Series, you can secure remote workers or the micro-office. Any Cisco Aironet or Catalyst access point can function as an OfficeExtend Access Point (OEAP). With an OEAP, an employee at home or in a temporary micro-office will have access to the corporate SSID and the corporate network without the need to set up a VPN or have any advanced technical know-how. Supporting four spatial streams, Multiuser Multiple-Input Multiple-Output (MU-MIMO) enables access points to split spatial streams between client devices to maximize throughput.Supporting two spatial streams, MU-MIMO enables access points to split spatial streams between client devices to maximize throughput. The flex profile is used for configuring the VLANs on the AP when the VLAN is overridden by the AAA that is used for the local switched SSIDs. Monitor—In the monitor mode, specified Cisco APs can exclude themselves from handling data traffic between clients and the infrastructure. These APs act as dedicated sensors for location based services (LBS), rogue AP detection, and intrusion detection (IDS).

Note: When you select another AP that is not the current standby to be the preferred controller, the current standby goes down and the new EWC you have selected becomes the standby EWC. ethernet_port wired0, ip 192.168.1.46, netmask 255.255.255.0, gw 192.168.1.1, mtu 1500, bcast 192.168.1.255, dns1 192.168.1.1, vid 0, static_ip_failover false, dhcp_vlan_failover false Both the Cisco Catalyst 9115AX and 9120AX Series access points share the same AP image file – ap1g7 – while the 9117AX Series image is ap1g6 and C9130 Series AP image is ap1g6a, which is included as part of the C9800-AP-universalk9..zip file. For HTTP transfer mode, specify the path to the access point image file on your local machine.Decide on the first AP to set up. This AP must support Cisco EWC functionality. You can also connect multiple Cisco Catalyst 9100 Access Points running the EWC to the switch.

HA pairing will be different. For the initial bring-up, the EWC active will wait until all APs join. It then selects the designated standby (via either auto-selection or configuration) and communicates that role and the HA parameters (local/peer IP, keepalive interval, priority, etc.) to the selected AP via a CAPWAP control message. Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz This High Availability (HA) architecture is based on the Cisco Catalyst 9800 HA architecture, with a few additions: Create the policy tag (if non-default needed) and map the SSIDs above to the policy profiles as required. CAPWAP image: When a CAPWAP image is installed on an access point, it can operate only as a CAPWAP access point and does not support the controller function.

https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9800-series-wireless-controllers/q-and-a-c67-743152.html . A guided workflow has been created for easy navigation through the steps required to set up the network on the Cisco Catalyst wireless controllers.